INTEX
Krystal Clear cartridge filter unit with timer
- Powerful cartridge filter unit
- Includes original filter cartridge type A
- Includes 2 connector hoses Ø 38 mm with 2” screw connection
- Timer Included
- Intex Hydro Aeration Technology
Sold Out
The selected product is currently not available. As soon as the product is on stock, we will send you an E-mail.
Product information
Intex cartridge filters deliver crystal clear water and great filtration results. This system, model , features circulation output of or pump output of , the connection totals / . All conventional above ground pools with a hose connection can be connected . The suitable filter medium for your Krystal Clear cartridge filter unit with timer is the Intex filter cartridge type . 2 swimming pool hoses with a length of 1,50 m, for Intex pools (connection fittings not included). The Intex Hydro Aeration Technology improves the circulation, filtration, water clarity and the air quality of your pool. The filter unit can be used with water temperature up to 35 °C maximum.
Intex Hydro Aeration Technology
- Hydro Aeration Set for your Intex pool
- Easy installation
- Can be retrofitted any time
Improved circulation and Filtration
Fine particles in the water clump together and settle to the bottom of the pool during the aeration process, making it easier to filter and remove sediments through the filtration system. The improved filtration and circulation make the pool water healthier and more comfortable.
Improved water clarity
By mixing air with water, the aeration process includes oxidation of iron and manganese, eliminating staining in water. The result is sparkling pool water that looks and feels great!
Increased negative ions at the water surface
Increased negative ions have been proven to improve the air freshness around the pool as it removes air pollutants and neutralizes free radicals that affects air quality.
Filter system:
Salt water suitable: yes
Water capacity: 33.300 l
Circulation capacity: 4.164 l/h
Boiler size: 126 mm
Connection size: Ø 38 mm
Valve type: no
Sound pressure level: ≤ 80 dB(A)
Water temperature: 5°C - 35°C
Usable filter medium: Filter Balls
Quantity of filter medium used: 60 g
Usable filter medium: cartridge filter
Quantity of filter medium used: A
Filter pump:
Power supply: 220-240V~ / 50Hz
Input power maximum: 165 W
Transformer: yes
Internal operating voltage: 12 V
Pump capacity: 5.678 l/h
Operating principle: non-self-priming
Pre-filter: no
Timer present: yes
Protection class: IPX5
Cable length to unit: 1,50 m
FAQs from category Cartridge filter systems:
Fill the unit with water and open the air release valve attached to the lid until water runs out. This is how you vent the system. Check all connections and hoses for leaks or holes. Retighten connections or hose clamps, seal them with Teflon tape and replace the defective parts if necessary.
Check the cartridge filter for the degree of contamination and clean it with a garden hose or replace it with a new filter. Check the water level and the height of the suspension skimmer; if the water level is too low, too little water flows into the pump. Vent the system. Open the air release valve on the cover until water runs out.
Check your socket for power, test another socket if necessary. Never run the pump without water, the pump can run dry and burn out. Check the mains plug or the connection cable for damage.
Check the cartridge daily and clean it with a garden hose as needed. If cleaning no longer achieves the desired success, replace it.
Flocculants must not be used with the cartridge filter system, as this could cause the cartridge lamellae to stick together. This means that cleaning is no longer guaranteed. This also applies to Quattrotabs, a component of these tablets are flocculants.
All Steinbach and INTEX filter systems (sand filter systems, cartridge filter systems & filter pumps) are suitable for salt water as long as the salt content in the water is below 0.5 % (salt electrolysis). Before winterising, clean the filter system thoroughly with standard bathroom cleaner, clear tap water and a lint-free cloth.
All filter systems and filter pumps have a sound pressure level* of < 70 dB(A).
*The emission volume is comparable to a large household appliance.
If the pressure is too low, the pre-filter is dirty and the pump is not getting enough water. Clean the pre-filter and check the suction line and the water level.
If the sand is newly filled in, or the sand is already very fine due to the use of several seasons, small sand particles may still be present. The solution is to backwash several times until the water comes out clear, or to fill in new sand.
The filter system should always be the first part in the water treatment system. The rest of the pool accessoires should only be connected after the filter system. A heat pump should ideally always be the last part in the water treatment system, so that the filtered, treated water flows through the heat pump and the path of the heated water into the pool is as short as possible.